Many people tend to spend more time and energy on the choice of home in home decoration, especially the purchase of aluminum alloy doors and windows, often ignoring the installation of aluminum alloy doors and windows. In fact, the installation of aluminum alloy doors and windows is also very important. Yes, pools are slightly different. There will be various problems when using it in the future. Therefore, it is necessary to understand the installation knowledge of aluminum alloy doors and windows. Today, the editor will sort out the installation steps of aluminum alloy doors and windows for you. Let's find out together. let's go!

Installation steps of aluminum alloy doors and windows

1. Line positioning:

1.1. According to the orientation, size and elevation of the doors and windows in the plan, measure the edge of the doors and windows according to the center line of the doors and windows. For multi-storey or high-rise buildings, the edges of the upper and lower doors and windows shall prevail, and the edges of the doors and windows shall be drawn out with hanging wires or theodolites. Where the symbols intersect the doors and windows of each floor, a single non-straight opening shall be chiseled.

1.2. The horizontal direction of doors and windows should be based on the horizontal line of the indoor floor + 50cm, measure the window height upwards, and the elastic line is a straight line. It is imperative that each floor adheres to a consistent window height.

2. Aluminum alloy suspension device

Fix the overhang on the aluminum alloy window according to the requirements of the construction drawing, and ensure that the direction is correct and the device is firm.

3. Anti-corrosion treatment:

3.1. When the anti-corrosion treatment plan for the outside of the door and window frame and external parts is required, it shall be treated according to the planning requirements. If there is no requirement in the plan, it can be protected with anti-corrosion paint or plastic film to prevent the cement mortar from directly contacting the exterior of the aluminum alloy doors and windows. Electrochemical reaction corrosion occurs in aluminum alloy doors and windows.

3.2. When installing aluminum alloy doors and windows, if joint iron is used to fix them, the metal parts of iron parts and fixing parts should be made of stainless steel, otherwise anti-corrosion treatment is required to avoid electrochemical reaction and corrosion of aluminum alloy. Doors and windows.

4. Aluminum alloy doors and windows are installed in place:

According to the positioning line of the positioned door and window, install the aluminum alloy door and window frame, adjust the horizontal, vertical and diagonal length of the door and window frame in time to meet the quality standard, and then temporarily fix it with a wooden wedge.

Installation steps of aluminum alloy doors and windows

5. Fixing of aluminum alloy doors and windows:

5.1. When the iron parts are pre-buried on the wall, the iron feet of aluminum alloy doors and windows can be directly welded to the pre-embedded iron parts on the wall, and the welding place needs to be derusted-proof.

5.2. When there is no embedded iron on the wall, the iron feet of aluminum alloy doors and windows can be fixed on the wall with metal expansion bolts or plastic expansion bolts.

5.3. When there is no embedded iron on the wall, an electric drill can be used to drill a hole with a depth of 80mm and a diameter of 6mm on the wall. Use L-shaped 80mm×50mm 6rmn steel bar to stick 108 cement slurry on the long end. Then, punch it into the hole. After the 108 cement slurry is finally solidified, the iron legs of the aluminum alloy doors and windows are welded to the pre-embedded 6mm steel bars.

6. Treatment of gaps between door and window frames and walls:

6.2. After the aluminum alloy door and window device is fixed, the sunshade project inspection should be carried out first. After passing the test, the gap between the door and window frame and the wall should be dealt with in time according to the planning requirements.

6.2. If there is no floor plan, elastic insulation material or glass wool felt strips can be used to fill the joints layer by layer, leaving 5-8mm deep grooves for joint filling grease or sealant on the outer and outer surfaces.

Installation steps of aluminum alloy doors and windows

7. Door and window sash and door and window glass device:

7.1. Door, window, window sashes and door and window glass should be installed after the inspection of the outer wall of the cavern.

7.2. After the door and window frame device is fixed, slide the door and window, and the glass door leaf is put into the frame groove as a whole, and the gap with the fan can be adjusted.

7.3. Open the doors and windows in the frame and fan frame to assemble the wall, fix the glass after the equipment is fixed, that is, first adjust the gap between the frame and the fan, then insert the glass into the fan and adjust the direction, insert the sealing strip and sealant.

7.4. The floor spring door should be installed after the door frame and the floor spring host are fixed. First insert the glass into the door frame and put them into the frame together, adjust the gap between the frame leaves, and fill the sealing strip and sealant of the door glass.